GENERAL INFORMATION

1. Begin the unpacking process of the crate that contains the TYTAX machine. Open one of the sides, and take the elements from the inside to the place where you are going to assemble the machine. Then, take of the rest of the boards that build the crate.

2. The floor in the room has to be flat, even and leveled.

3. The assembly process of the TYTAX machine has to be done by 2 adult persons !!!

4. REMEMBER! - At the beginning, the connections have to be tightened slightly by hand. When the rest of the elements is put together, tighten all the connections.

ATTENTION: After assembly of TYTAX machine, to safely perform a training you should first watch the video here: BASICS In it, you will see how to correctly and safely use TYTAX equipment.

ATTENTION: On drawings we show MINIMAL ROOM SIZE inside which TYTAX machine can be installed. Drawings do not present machines’ measurements.

TYTAX T1-X

gym gear

TYTAX T1-X

gym at home equipment

TYTAX T1-X + option O

rent exercise equipment

TYTAX MACHINE - a 180° look at it. You can always rewind the video during the assembly of your machine to see it in detail. Below you can see a step by step manual about how to assembly your TYTAX machine.

BOTTOM VIEW

TOP VIEW


Remember, if you have problem with unscrewing a screw with a hex key (included with TYTAX machine), you can apply simple lever, to increase a strength as you unscrew a screw - see the video.

TYTAX machines are produced in Europe, where metric system dominates. It is important information because in a case when a head of a hex key breaks (or will be damaged), then our factory will have to send to a client a new set of tools/keys. The very same size of keys, you can get at good tool-shop or at car mechanic ( brands like Mercedes, Audi, BMW, Porsche work with the metric system too). Do not forget to take your old key with you as a exemplar.


Remember to keep the screws after dismantling TYTAX crate. They might be useful later. TYTAX machine is produced in Europe when millimeter unit is used, not inches. You will not be able to purchase similar screws in USA for example.

home gym garage

When inserting or taking out pivot with a wheel inside/outside machine’s body remember, that hole from one side has larger diameter (start inserting from this side), and from the other side it has smaller diameter. When tightening the pivot, do it gently so the wheel could move freely.






Remove machine body’s poles. If even after unscrewing screws it is still hard to remove the pole, try to ease off screws in next pole – to reduce tension. Do not forget to screw them after that.


Each of the connection between the parts of the machine has its own characteristic number. If an element is marked with number "1" or "2" or ... "8" or "12", then it can be connected with other parts that have the same number. Apart from the number, each connection is marked with an arrow that points the relation between other connected elements.


To unscrew this beam, it might be necessary to perform a lever on hex key – same as we have shown on one of the first videos above.

To unscrew this beam, it might be necessary to perform a lever on hex key – same as we have shown on one of the first videos above.


To fit flanges with screws of this element to machine’s body, you can tenderly ease off screws in machine’s body (footing) – to gain some space.



First, screw in screws with your hands.

It is important, that when you will be screwing this element with a key, to set smith machine frame on hooks (with handles).



Leave one spacer on each pivot. Then put the covers, and then again – a spacer. Last step is to screw all in with a key.









It is a sensitive point and you should pay attention at it during assembly. To attach left and right arm, tighten the screws first. Make sure that screws are screwed in directly inside machine’s body. Damaging the thread will result in replacing the whole element. To eliminate problem with incorrect screwing in screws inside machine’s body remember to gently manually tighten them first.




Important – do not screw these beams with a key, try to lightly screw tchem with your hand. In the last step of assembly, you can screw these beams with a key.


Red color - flanges connection in the curve line - wrong. Loosen the screws on the flange, and set straight the upper part of buterfly
Green color - flanges connection in a straight line - good

home gym garage




In the last step screw this element as shown in the video, and screw all loose screws.




INFORMATION

This was the last step in assembling the TYTAX machine. The multi-gym is now ready to use.
After assembly of TYTAX machine, to safely perform a training you should first watch the video here: BASICS In it, you will see how to correctly and safely use TYTAX equipment.

Information about grips/accessories for the TYTAX machine can be found here: ACCESSORIES
Information about cables for the TYTAX machine can be found here: CABLES
Information about sockets/slots in the TYTAX machine, what they are used for etc. can be found here: SOCKETS
Information about preparing for an exercise can be found here: INSTRUCTIONS

* If in any of the above materials about the usage of TYTAX machines you will see a mistake, please contact us under this email: support@titan-gyms.com

ASSEMBLING OTHER TYTAX ACCESSORIES

In our offer you can also find such TYTAX products like the stand for the dumbbells, stand for accessories etc. Please see the video about assembling those elements below.


RACK OF DUMBBELLS - SH-6


RACK OF DUMBBELLS - SH-12


RACK OF DUMBBELLS - SH-18